THE ART OF PLUMBING FUNDAMENTALS WHEN YOU INSTALL A BATHTUB

The Art of Plumbing Fundamentals When You Install a Bathtub

The Art of Plumbing Fundamentals When You Install a Bathtub

Blog Article

Book

Just how do you actually feel in regards to A Step-by-Step Guide to Installing a Bathtub?


Installing A Bathtub
Installing a bathtub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is readily easily accessible, the job can relocate immediately; if you have to open up a wall surface to get rid of the old bathtub and also place the brand-new tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and embeded in the new one. Ensure you have qualified yourself for the job and are comfortable attempting it. Instead of working with a professional to take over a halfway-completed job, it is much better to consider using one before you begin. Opportunities are you may need a professional plumber to make tube links.
This article will help you set up a brand-new bathtub in your shower room if you have actually currently purchased a new bathtub and also do not require to change the arrangement of your previous water pipelines.
Your tools and product checklist should comprise the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is separate the supply of water. After doing so, turn on the taps to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be quite problematic due to the restricted accessibility that is commonly the situation.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipes. When the supply pipes have been eliminated, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
    Prior to carrying on to fit the brand-new faucets, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipes.
    If you need to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next off, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in location in between the faucet and the sink. Secure the tap in position with the supplier provided backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Installing the Bathtub


    Using both wood boards under its feet, put the bathtub in the required placement. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny factors.
    The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the bathtub until the level reads degree.
    To install taps, fit all-time low of the outermost flexible tap adapter to the ideal supply pipe by making a compression sign up with; then do the same for the other faucet.
    Switch on the supply of water as well as inspect all joints and also new pipework for leakages and also tighten them if needed. Fill the bath tub and additionally examine the overflow outlet and the regular electrical outlet for leakages.
    Finally, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the tub ought to wait until the bath tub has actually been utilized at least when as this will settle it right into its final setting.

    Preparing for the Installment


    First of all, the supporting structure supplied with the bathroom should be fitted (if called for) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
    Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
    Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.

    Tiling Around the Tub


    In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a stiff seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, leading to complications with moisture and also possible leaks to the ceiling listed below.
    You can pick from a selection of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the bathtub with water before sealing, to enable the motion experienced when the tub remains in usage. The sealer can split relatively very early if you do not think about this activity prior to sealing.
    Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof glue as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    As an enthusiastic person who reads about A Step-by-Step Guide to Installing a Bathtub, I think sharing that piece of writing was a great idea. For those who liked our blog entry plz remember to share it. Thanks a lot for taking the time to read it.


    Go Services

    Report this page